Featured Used Mining Equipment in Stock. Machinery & Equipment
CONVEYOR, BELT, 36″ X 4-MILE, OVERLAND CONVEYOR
Stock Number: D742389
Location: East Coast
Overland belt conveyor, 36″ wide X 4-mile belt with 42″ wide frame and 36″ idlers, 66″ deep truss. Includes dual 400 HP Siemens drives. System is galvanized and includes Eriez magnet, 3/4 of conveyor conveyors, belt scales, etc. Set up to run from mine to power plant. Used less than one year. New in 2010.
CRUSHER, IMPACT, VERTICAL, CEMCO, MDL MDEV80, 400 HP
Stock Number: S738844
Location: San Dimas, CA
Cemco Turbo vertical shaft impact crusher, VSI, model MDEV80, Turbo80. Crushing chamber measures 6′ diameter X 4′ high sidewall, with 35″ diameter Superchipper rotor assembly. Product is fed through 15″ diameter center top opening thru rotor with 12″ x 8″ openings, spreading feed material into crushing chamber. Inside wall includes heavy duty anvil ring with stationary anvils along circumference of chamber. Rotor is driven by twin drives, 250 HP and 150 HP (460 volt, 1785 RPM, 3/60Hz) thru V-belt assemblies, connected to common sheave. Product discharges through 36″ x 15″ split discharges. Top cover is removeable with swing assembly, controlled by manually operated hydraulic cylinder. Serial# 4156.
CRUSHER, ROLL, 78″ X 60″, 2-ROLL, FAM, (2) 350 HP, PRIMARY
Stock Number: S738503
Location: Timmins, ON, Canada
Double roll crusher, 78″ diameter x 60″ wide (2000 mm x 1500 mm) rolls, heavy duty teeth, manufactured by FAM, type ZWB 2015 HSm, up to 24″ feed size, (1) roll is hydraulically adjustable for roll gap spacing, rolls driven by twin 350 HP, 4000 volt, 1187 RPM, 60 Hz motors thru gear reducers. Complete with lube system, discharge chute, hydraulic pump station, controls, etc. Previously used as primary crusher at phosphate minerals processing facility. Apron feeder also available. Equipment was dismantled and is now being stored at crane yard for easy loading.
KILN, 8′ X 92′, ROTARY, METSO, 2400 DEG F, PORTED, 2013
Stock Number: C740503:
Location: Fort Meade, FL:
Rotary Kiln, 8′ diameter X 92′ long, manufactured in 2013 by Metso, complete with gas burner, to 80mm BTU’s per hour. Last used on phosphate rock in research and development plant; used less than 1,000 hours. System includes all motors, fans, electricals, structural steel, instrumentation, and all drawings. Shell has 21 ports (which can be covered) for introducing air, 30 Hp motor and gearbox to chain and sprocket drive, 12 tons per hours at 60 minutes residency time.
MILL, BALL, 11.5′ X 17′, KVS, 1000 HP, REFURBISHED IN 2013
Stock Number: C742220
Location: Fort Meade, FL
11.5′ diameter X 17′ long ball mill, manufactured by KVS (Kennedy Van Saun), includes 1000 HP open winding synchronous motor. Features trommel discharge and feed tank. Refurbished in 2013, which included installation of new oil jacking system, oil lube system for Babbitt bearings, new titanium steel water jet-machined discharge grates, and motor refurbishment. Set of new babbit bearings available. Previously operated as a closed circuit dry mill with grinding capacity of 40 metric tons per hour with output fineness of >80% passing 200 mesh. Motor operating speed of 15.8 RPM charged with approximately 78 tons of 1″, 2″ and 3″ steel balls. Last used at a phosphate processing facility and in good condition.
MILL, BALL, 13′ X 21′, ALLIS CHALMERS, 2000 HP, R/L
Stock Number: S738509
Location: Timmins, ON, Canada
Allis Chalmers Svedala ball mill, 13′ diameter x 21′ long, rubber-lined mill, with Siemens-Allis 2,000 HP, 4000 volt, 200 RPM synchronous motor, Eaton airflex clutch. Includes trommel discharge, ball mill rejects conveyor, lube system, etc. Offered complete with controls. New in 1979. Completely rebuilt in 1998, serial number C-2485. Previously used at phosphate minerals processing facility. Also available pumps, spare parts, drives, controls to comprise of complete mill system. Equipment was dismantled and is now being stored at crane yard for easy loading.
MILL, BALL, 22′ X 38′, METSO, 10,000 KW, UNUSED (2)
Stock Number: C740223
Location: Europe
(2) Ball Mill, 22′ X 38′, (6.7m X 11.6m), manufactured by Metso in 2007. Each complete with two 5,000 KW motors (13,410 total HP). 10,000 V, 50 Hz. Complete with controls and electricals. Unused and never installed. Rated at 813 tons per hour nominal capacity. Spare parts including motor also available.
MILL, BALL, 7′ X 5 1/2′, 100 HP, SKID MOUNTED, STEEL LINERS
Stock Number: C740611
Location: Chowchilla, CA
7′ diameter X 5 1/2′ long ball mill, includes 100 hp motor, 1180 RPM, 220/440 V, Frame 444T, and spare motor. Scoop feed, 8″ wide straight bull gear, 18″ diameter feed and discharge, babbitted bearings. I-beam stand measures 5′ X 13′. 18 tooth pinion gear, 10″ belt drive sheave, steel liner Unit is missing gear guard, includes 6 barrels of balls on pallets.
MILL, SAG, 18′ X 10-1/2′, FULLER, 1500 HP, R/L,
Stock Number: S738506
Location: Timmins, ON, Canada
SAG mill, 18′ diameter x 10-1/2′ long, manufactured by Fuller, rubber-lined, driven by 1500 HP, 4160 volt, 1192 RPM, continuous motor, 5010 frame, thru Moventas gear reducer, 4.5:1 gear ratio, 264.4 output RPM, mfg# C001338. Complete with Robicon Perfect Harmony VFD drive & 2-piece gear inching motor. Includes stationary & ball feed chutes, discharge chute, reject chute, retractable feed chute, etc. Offered with discharge belt conveyor, & SAG rejects conveyor, complete with lube system, manufactured by Howard Marten, Model number M8375F, order# M42483, includes oil pumps, cartridge filters, etc. Previously used at phosphate minerals processing plant. Also available McLellan liner handler, 4000 lb. capacity, with hydraulic pump, approx. 25 HP; pumps, spare parts, drives, controls to comprise of complete mill system. New in 1998. Equipment was dismantled and is now being stored at crane yard for easy loading.
MILL, SAG, 36′ X 20.5′, METSO, 20,000 HP, UNUSED
Stock Number: C740224
Location: Europe
SAG Mill, 36′ diameter X 20.5 long (11m X 6.2m). Manufactured by Metso in 2007, Unused and never installed. Complete with ABB 15,000 KW (20,115 HP), 10,000 V, 50 Hz gearless drive, control room, and transformers. Nominal rating of 1625 tons per hour (13 MTPA). Components are in original crates and inspected and maintained yearly.
Comments